Choose Your Language
Versalift East - Bucket Trucks and Aerial Lifts
Welcome to Versalift East - Bucket Trucks and Aerial Lift Trucks
Search the Versalift East Website for:
  Versalift Bucket Trucks

Versalift VO-43-I Insulated Articulated
Aerial Bucket Trucks

Versalift VO-43 BrochureBucket Truck VO 43 Versalift

INSULATED UPPER BOOM
The 8 in. x 10 in. (200 mm x 250 mm) rectangular upper boom is constructed of high strength filament-wound epoxy resin fiberglass. The fiberglass has a gel coat and a high gloss durable urethane finish for added weather protection and water beading. The fiberglass boom is certified for 46 KV and below in accordance with ANSI A92.2 Category C dielectric rating requirements. The upper boom articulates a total of 2400 relative to the lower boom from -100 to +2300. A side by side boom design allows low Versalift Bucket Truckstravel height and improved platform access. The upper boom articulation is accomplished by a double acting hydraulic cylinder and 4-bar mechanical linkage. The system does not use any cables and
the booms can be stowed in any sequence. A double acting holding valve is provided. An upper boom storage cradle mounted on the turret assures solid boom support in the stowed position. A ratchet-type boom tie-down strap is included.

LOWER BOOM
The lower boom is designed and constructed from high strength, 12 in. (300 mm) square, steel tube. Boom articulation is 1150 from horizontal to 250 past vertical. Articulation is achieved by using a double-acting hydraulic cylinder equipped with two integral holding valves.

ELECTRICAL INSULATION SPECIFICATIONS
The upper boom is tested and certified as standard for electrical work at 46kV and below in ccordance with ANSI A92.2 Category C dielectric rating requirements. The chassis insulating system
(lower boom insert) is also tested and certified according to ANSI A92.2.

CYLINDERS
Both the upper boom and lower boom cylinders are the threaded end-cap design. Both boom cylinders are equipped with two integral holding valves to prevent creep of the booms and to lock the booms in position in the event of a hydraulic failure.

CONTINUOUS ROTATION
Rotation is continuous and unrestricted in either direction. The rotation system consists of a hydraulically driven worm and spur gear acting on a shear-ball rotation bearing. The critical bolts holding the lift to the rotation bearing and the rotation bearing to the pedestal are grade 8. These critical bolts are torque seal marked to provide a quick means of detecting any loosening. An eccentric ring gearbox mounting allows for precise backlash adjustments sequence.

MECHANICAL PLATFORM LEVELING
Platform leveling is achieved automatically through a completely enclosed parallelogram system. The major components of this system include 1 in. (25 mm) diameter fiberglass leveling rods and No. 100 high strength roller chain. There are no cables used in this system. The fiberglass leveling rods maintain the insulation gaps in all boom positions and are 100% tested at twice the rated load. The tension is adjusted by means of a threaded rod in the upper and lower boom and platform leveling is adjusted by another threaded rod at the turret.

LUBRICATION
Non-lube bearings are used at most pivot points. Only the rotation bearing and leveling chains require periodic lubrication.

GENERAL SPECIFICATIONS (Based on 40 in. (1.02 m) Frame Height)

  VO-43-I VO-43I Boom Travel
Horizontal Reach, Overcenter 34 ft (10.4m)
Horizontal Reach, Non-Overcenter 33 ft 1 in (10.1m)
Maximum Platform Capacity 400 lbs (183kg)
Lower Boom Lift Eye Capacity 1500 lbs (680kg)
   
With Standard Pedestal
Height to Bottom of Platform 42 ft 10 in (13m)  
Working Height 47 ft 10 in (14.60m)  
Stowed Travel Height 10 ft 3 in (3.1m)  
     
Hydraulic System    
Operating Pressure 2500 PSI (176 kg/cm2)  
Flow Rate 6 GPM (23 lpm)  
Filtration

10 micron return
100 mesh section

 
System Type Open center  
Power Source PTO Pump  

*NOTE:

  1. Specifications may vary without prior notification
  2. Required GVWR can vary significantly with chassis, lift mountings location, service body, accessories, and desired payload.

OPTIONS:

  • 400lbs. Platform Capacity
  • Platform Liner and Cover
  • Manual Platform Tilt
  • 900 Platform Rotation
  • Two-Speed Manual Throttle-Control
  • Emergency Power
  • Category B Dielectric Testing & Certification
  • Outriggers or Torsion Bars
  • Tool Port Pressure & Flow Control
  • Second Set of Tool Power Outlets

Bucket Articulation
Articulation allows for easy
access to compartments.

VO-40-MHI Bucket Truck
Platform tilt allows
for easy cleaning.
Versalift Bucket truck
Torsion bars provides additional
chassis support.
 
Utility Equipment Partners